Harris Rf-5022 Manual
Harris RF-3200ET Portable Transceiver. Operator's Manual Accessory Bag. RF-5022 RF-350 RF-3201 RF-3200. Does not operate normally,without access to settings frequencies and modes,only light, power, test, SQ and security.
Note since the person on the other end of the phone call is most likley at a regular phone they have no way of pressing PTT, so maybe that's handled for both sides of the conversation by the RF-3565. That would require something like the 3900 Hz tone in the GRA-39 to control the radio at the far end of the link. So why the 14-pin connector rather than just a U-229 type audio connector? There is 2-way digital coms between the RF-3565 and the field radio.
Schematic w 8P8C & RE3200 Connector wiring Ohms DC Red Wht Blk Red 0 White 1k428 0 Black 1k4 32.2 0 DB-15 Accessory Connector Pin Name I/O Note 1 SPKR+ Out 4 Ohm min 11 Vpp max 2 SPKR- 3 ACRXOUT Out 600 Ohm 4 ACCTXIN In 5 /ACCRQ In Key 6 GNDAUD Audio gnd 7 ACCTGC In external AGC 8 ACCTR+ I/O Tx On Realy closed 9 ACCTR- I/O 10 /RMTSW In gnd:Pwr On 11 SWA+ Out 13.6 VDC switched 800 ma max 12 RTS Out not used do not connect 13 GNDLOG Logic gnd 14 RXD Out data 15 TXD In data. The other half suitcase has the antenna coupler built into it and also has the accessories. By seperating the two half suitcases the antenna coupler can be located close to the antenna which is a much better thing to do than using coax between the coupler and antenna proper. Note that many antenna couplers take some time to tune up on a new frequency and so when they are used for ALE operation the whole process gets slowed down or does not work at all.
Doug Compatible Radios AN/PRC-117 RF-2301 (w/ RF-2370 or F-2380) RF-5020 RF-5022 RF-350 RF-3201 RF-3200 (see ) Telephone over Radio When a telephone call is passed over a simplex radio link there needs to be a way to handle the PTT signal to the radio since normal telephones are full duplex. The uses a 3900 Hz tone (above the 300 - 3000 Hz audio passband) for this purpose. Maybe the RF-3565 follows the same convention? Note since the person on the other end of the phone call is most likley at a regular phone they have no way of pressing PTT, so maybe that's handled for both sides of the conversation by the RF-3565. That would require something like the 3900 Hz tone in the GRA-39 to control the radio at the far end of the link. So why the 14-pin connector rather than just a U-229 type audio connector? There is 2-way digital coms between the RF-3565 and the field radio.
Press CH ▼or CH ▲ until the channel or station you want to add to (or remove from) your favourites list is highlighted. To see a list of the radio stations in your favourites list, press TV/RAD on the remote control.
The A2 audio PCB has an optional resistor (R30 - 10K) to be installed when a condenser mike is to be used. The acid test is to transmit and pay attention to the output power on the bar graph in the lower left of the LCD.
Note that the antenna coupler is not operative in receive mode. Accessory Bag Missing from my set. The DC power cord that's normally in the bag is in the lid of this set. ALE The 3200 uses the 'Old' ALE, not the current version. So for some applications it will not work.
Harris RF-3200ET Portable Transceiver © Brooke Clarke 2008 Radio Behind the blank panel to the right of the knob is the keypad Antenna Coupler & Accessories Background is a major military H.F. Radio maker and is currently supplying a number of models. The RT-3200E is a (no longer in production) table top digital H.F.
The star cast of the Serial is A.R.C. Chakravakam telugu serial cast names.
In my case it's 150W transmit and 0 Watts reflected when I whistle. But, I've heard that these mikes work fine for whistling, but not for voice, so.. Using a GR 1307 Transistor Oscillator driving the 1552-B Sound-Level Calibrator held touching the mide at 400 and 1000 Hz gives the following transmit power: Freq Hzs Tx Power Watts 400 30+ 1000 150- So the next thing is to try some different mikes. But first need to get some of the 8 socket Foster mike connectors (aka: Radio Shack 274-025 or274-025b, Philmore 61-608B or T700B).
Notes: General Description: The Harris RF-5710 HF Modem, nomenclatured MD-5077(V)3/U, is a compact unit having the ability to generate the following HF waveforms using the same hardware: MIL-STD-188-110A Serial, Frequency Shift Keying (FSK), North Atlantic Treaty Organization Standard Agreement #4285 (NATO STANAG 4285), and NATO STANAG 4529. All waveforms and their variables are selected by front-panel controls. User menus, prompting, and operational status of the modem is indicated by a front-panel mounted liquid crystal (LCD) display. Full remote control capability is provided by an RS-232C interface and can be accessed from any ASCII terminal connected to the modem's remote control port. For future improvements, the modem is Firmware upgradeable. Waveforms: The single (serial) tone mode is based upon Phase Shift Keyed (PSK) modulation at a constant rate of 2400 symbols per second.
The binary FSK waveform is implemented with digital signal processing (DSP) techniques. The interface support both Synchronous or Asynchronous data connections and the modem allows for half and full-duplex operation in most modes. Capabilities: The versatility and speed of the modem make it suitable for a variety of applications including: • Narrowband Secure Voice • High-Speed Burst Data • Digital Facsimile • Slow-Scan Television • HF, Microwave, Land-Line • Narrowband Satellite Connection of the RF-5710 HF Modem to the Harris RF-230 HF Transceiver will require the user to locally manufacture an interface cable as shown in the schematic bellow. You will require a suitable length of 5 conductor shielded cable to assemble the interface cable.
Introduced in 1987 and the phaseout started about 10 years later because support was limited. There is also a rack mount kit/version (see below) of the 3200 radio. This half contains the RT-3200E radio. The connectors at the top are the rear panel connectors on the RF-3200 brought out on a seperate panel.
When removed there was black goo on my fingers. The Power Connector Kit I sell () that mates with the POWER connector on the and radios mates with J1. To access the PCB: 1) remove keyboard (leave battery slide clamped) 2) remove switch end plate RF-3565 Printed Circuit Board I'm guessing the 44QFP Harris RF p/n 10376 is a micro controller (12 MHz clock). The blue 11 pin SIP socket is for the 4x5 keyboard.
Radio Set AN/TRC-510(V) (NSN ####-##-###-####) GENERAL DESCRIPTION The AN/TRC-510(V) is a self-contained, transportable, High Frequency Quick Reaction Terminal (HFQRT). The heart of the HF radio communication system is founded on the Harris FALCON series of tactical communication products. Major components include the Harris RF-5022R/T(V) (RT-5104(P)/U) transceiver, the RF5000T-400A (AM-7419/U) 400 Watt RF linear power amplifier and, the RF-382A-02 (CU-2397A/G) fast tune antenna coupler. Other components include the RF-5285MD (MD-1273/U) High-speed Data Modem option, the RF-5122ALE(E) (CD-5034/U) Automatic Link Establishment option, 2 x RF-5051PS (OP-182/U) power supplies, the HT-21B transportable broadband antenna, the AS-2259/GR portable NVIS antenna system, and the AS-5216/TRC-510 transportable ground stake antenna kit.
So for some applications it will not work. Harris System 3000 Components. MIL-STD-141A FED-STD-1045A RF-3234E-02 ALE Remote Control - telephone type remote, 1000 foot max RF-3234ALE-E VIP Remote Contgrol System - two parts: RF-3272E Controler & RF-3234E-02 Control RF-3246 Narrow Band Filter - 300 Hz RF-3247 Wide Band Filter - 300 to 3100 Hz used for voice security or digital modes RF-3238 Continuous Duty Blower Kit - for RT-3200E?? - Two-tone Alarm for front panel?? - 125 Watt SS T/R Switch?? - External Reference Oscillator Antenna Couplers & Accessories RF-3281 Voice Duty Digital Automatic Coupler. Power Supply Options RF-3236 Continuous Duty Base Unit P.S.
It is therefore impossible to set a synchronous mode of operation on these devices. The use of the synchronous clock mode can only be employed with terminal equipment that is designed for synchronous modes of operations. Examples of synchronous terminal equipment are most cryptographic devices (i.e. TSEC/KG-84C), some fax machines and, specially equipped computer terminals. Consult your equipment's technical specifications prior to employing the synchronous data port configuration. Related links: Revised: June 08, 2017 (c) 1998-2018, Richard Lacroix. All rights reserved.
This may be due to a problem with the microphone, how it's wired or one or two resistors on the A2 Audio PCB. Pin Function 1 Carbon Mike Input 2 Filtered Supply Voltage 3 Ground for Handset or Headset 4 Earphone 5 PTT (gnd to talk) 6 PTT Ground 7 Mike Ground 8 Mike Input Provision is made in the mike connector wiring to accommodate either an electrect-condenser or air-condenser mike (pin 8) or a carbon mike (pin 1). The A2 audio PCB has an optional resistor (R30 - 10K) to be installed when a condenser mike is to be used. The acid test is to transmit and pay attention to the output power on the bar graph in the lower left of the LCD. The upper scale is in Watts with a max of 150 Watts. When the trap door is opened on the right (slide up the open) and the RFL button is pressed the bar graph displays reflected power.
A list of radio stations appears. Pressing TV/RAD again redisplays the TV channels.
The software and DTE settings in table 1a are suggested for all FSK modes of operation and settings in table 1b are suggested for all serial modes of operation. NOTICE: See table 2 and table 3 for modem set-up information. Your modem configuration will have to be changed in accordance with table 3 if you are transmitting Baudot or ASCII alphabet. Baudot is used for the FSK modes and ASCII is used for the serial modes.
The Power Connector Kit I sell () that mates with the POWER connector on the and radios mates with J1. To access the PCB: 1) remove keyboard (leave battery slide clamped) 2) remove switch end plate RF-3565 Printed Circuit Board I'm guessing the 44QFP Harris RF p/n 10376 is a micro controller (12 MHz clock). The blue 11 pin SIP socket is for the 4x5 keyboard. (5 rows + 4 coul = 9 pin matrix) There is a MAX232EPE so there's RS-232. The 8 pin Molex plug is for the battery cable. The use for the white 6 pin header with a jumper is unknown as is the function of the 8 red DIP switches. Technical Description Although there are some similarities with the PRC-77 the radio pin out is it's own thing.
Harris RF-3200ET Portable Transceiver © Brooke Clarke 2008 Radio Behind the blank panel to the right of the knob is the keypad Antenna Coupler & Accessories Background is a major military H.F. Radio maker and is currently supplying a number of models. The RT-3200E is a (no longer in production) table top digital H.F. If you look at the left figure above you can see it at the bottom of the suitcase half.
Pin Note 1 Radio PRC-138 J2 Data Connector: RF-3565 J1 Guess 30 Aug 2011 A Fixed level receive audio out D B Fixed level transmit audio in F C Data Out K? E Battery Out or Remote Power On (jumper setting) N F TX Keyline (PTT) B H RLSD (Output, RS-232C or MIL-STD-188-114A levels) J Ground A & L K Remote async data in H? L Clear to Send (CTS) M Sync Clock In N Remote async data out K? P RTS J R Sync clk out P.
Accessory Bag Missing from my set. The DC power cord that's normally in the bag is in the lid of this set. ALE The 3200 uses the 'Old' ALE, not the current version. So for some applications it will not work. Harris System 3000 Components.
There is 2-way digital coms between the RF-3565 and the field radio. Front Panel Transceiver Interface Connector J1 BT02E12-14S Operator Instructions DIP switch for Options () 9V Battery was dead dated 08-98. I wonder if these units were removed from service because of a dead battery? You can see corosion on the left terminal. When removed there was black goo on my fingers.
Harris was the original inventor of the HF single tone demodulation technique and holds patent rights to the 'Data Directed Equalization' technique. Convolutional coding (1/2 rate) and Viterbi decoding are combined with interleaving to provide unequalled performance in HF channels. Data rates of 75 to 2400 bits per second (bps), and 4800 bps (uncoded), are provided. Automatic bit rate detection and correction are provided in receive mode.
If you look at the left figure above you can see it at the bottom of the suitcase half. The RT-3200ET is a Transportable version housed in a black metal suitcase that weighs about 49.5 pounds and is 21' wide x 15' high x 8' thick. This is inside the 22 x 14 x 9' airline carry on luggage size limit since the 15' number includes the handle. But the weight is probably going to require a penalty. The two halves of the suitcase can be separated. Introduced in 1987 and the phaseout started about 10 years later because support was limited. There is also a rack mount kit/version (see below) of the 3200 radio.
Harris Rf-5022 Manual
The upper scale is in Watts with a max of 150 Watts. When the trap door is opened on the right (slide up the open) and the RFL button is pressed the bar graph displays reflected power. In my case it's 150W transmit and 0 Watts reflected when I whistle. But, I've heard that these mikes work fine for whistling, but not for voice, so.. Using a GR 1307 Transistor Oscillator driving the 1552-B Sound-Level Calibrator held touching the mide at 400 and 1000 Hz gives the following transmit power: Freq Hzs Tx Power Watts 400 30+ 1000 150- So the next thing is to try some different mikes. But first need to get some of the 8 socket Foster mike connectors (aka: Radio Shack 274-025 or274-025b, Philmore 61-608B or T700B). The Mike is a Sure Prologue Model: 6L-B 500 Ohm Dynamic.
Harris Rf 5022
This half contains the RT-3200E radio. The connectors at the top are the rear panel connectors on the RF-3200 brought out on a seperate panel. There are two levels of password for the radio, one for user options and one for how the radio works. A prior owner taped them to the inside of the door over the keypad.